Toyota RAV4 manuals

Toyota Sienna Service Manual: Short to GND in Rear Curtain Shield Squib LH Circuit

DTC B1637/85 Short to GND in Rear Curtain Shield Squib LH Circuit

DESCRIPTION

The rear curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1637/85 is recorded when a short to ground is detected in the rear curtain shield squib LH circuit

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

1 CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (REAR CURTAIN SHIELD SQUIB LH)

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (REAR CURTAIN SHIELD SQUIB LH)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the curtain shield airbag assembly LH.
  4.  Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire.

    CAUTION: Never connect a tester to the curtain shield airbag assembly LH (Rear curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

    Insert the SST straight into the terminals of the connector.

    SST 09843-18060

  5.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Clear the DTCs stored in memory.
  8.  Turn the ignition switch to the LOCK position.
  9.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  10.  Check the DTCs.

OK: DTC B1637/85 is not output.

HINT: Codes other than DTC B1637/85 may be output at this time, but they are not related to this check.

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH

2 CHECK FLOOR WIRE (REAR CURTAIN SHIELD SQUIB LH CIRCUIT)

CHECK FLOOR WIRE (REAR CURTAIN SHIELD SQUIB LH CIRCUIT)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the floor wire.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the curtain shield airbag assembly LH and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory.
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs.

OK: DTC B1637/85 is not output.

HINT: Codes other than code B1637/85 may be output at this time, but they are not related to this check

USE SIMULATION METHOD TO CHECK

Open in Rear Curtain Shield Squib LH Circuit
DTC B1636/88 Open in Rear Curtain Shield Squib LH Circuit DESCRIPTION The rear curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly ...

Short to B+ in Rear Curtain Shield Squib LH Circuit
DTC B1638/86 Short to B+ in Rear Curtain Shield Squib LH Circuit DESCRIPTION The rear curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag ...

Other materials:

Removal
1. REMOVE V-BANK COVER SUB-ASSEMBLY (See page EM-28) 2. REMOVE NO. 1 ENGINE UNDER COVER (See page EM-26) 3. DRAIN ENGINE COOLANT (See page CO-6) 4. REMOVE NO. 2 AIR CLEANER INLET (See page EM- 28) 5. REMOVE BATTERY (See page EM-26) 6. REMOVE FRONT BUMPER ASSEMBLY (See page ET-3) 7. REMOVE ...

USB interface
General information Follow the information regarding the connection of mobile devices to the USB interface in the section on USB connections. In the center armrest A USB interface is located in the center armrest. Properties: USB port Type C. For charging of mobile devices. Charge current: ma ...

Air conditioning pressure sensor
ON-VEHICLE INSPECTION 1. INSPECT A/C PRESSURE SENSOR (a) Install the manifold gauge set. (b) Disconnect the connector from the A/C pressure sensor. (c) Connect the three 1.5 V dry cell batteries' positive (+) lead to terminal 3 and the negative (-) lead to terminal 1. (d) Connect t ...

В© 2011-2023 Copyright www.tsienna.net