Toyota RAV4 manuals

Toyota Sienna Service Manual: Open in Rear Curtain Shield Squib RH Circuit

DTC B1631/84 Open in Rear Curtain Shield Squib RH Circuit

DESCRIPTION

The rear curtain shield squib RH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1631/84 is recorded when an open circuit is detected in the rear curtain shield squib RH circuit.

DESCRIPTION

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

1 CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (REAR CURTAIN SHIELD SQUIB RH)

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (REAR CURTAIN SHIELD SQUIB RH)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the curtain shield airbag assembly RH.
  4.  Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire No. 2.

    CAUTION: Never connect a tester to the curtain shield airbag assembly RH (Rear curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

    Insert the SST straight into the terminals of the connector.

    SST 09843-18060

  5.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Clear the DTCs stored in memory.
  8.  Turn the ignition switch to the LOCK position.
  9.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  10.  Check the DTCs

OK: DTC B1631/84 is not output.

HINT: Codes other than DTC B1631/84 may be output at this time, but they are not related to this check.

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH

2 CHECK FLOOR WIRE NO.2 (REAR CURTAIN SHIELD SQUIB RH CIRCUIT)

CHECK FLOOR WIRE NO.2 (REAR CURTAIN SHIELD SQUIB RH CIRCUIT)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the floor wire No. 2.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the curtain shield airbag assembly RH and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory.
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs.

OK: DTC B1631/84 is not output.

HINT: Codes other than DTC B1631/84 may be output at this time, but they are not related to this check.

USE SIMULATION METHOD TO CHECK

Short in Rear Curtain Shield Squib RH Circuit
DTC B1630/83 Short in Rear Curtain Shield Squib RH Circuit DESCRIPTION The rear curtain shield squib RH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembl ...

Short to GND in Rear Curtain Shield Squib RH Circuit
DTC B1632/81 Short to GND in Rear Curtain Shield Squib RH Circuit DESCRIPTION The rear curtain shield squib RH circuit consists of the center airbag sensor assembly and the curtain shield airbag ...

Other materials:

Inspection
1. INSPECT UNDERDRIVE PACK CLEARANCE (a) Install the underdrive clutch to the transaxle case. NOTICE: Be careful not to damage the oil seal rings. (b) Install a dial indicator as shown in the illustration. (c) Measure the underdrive clutch pack clearance while applying and releasing comp ...

Installation
1. INSTALL TRANSFER ASSEMBLY (a) Apply sealant 1281 to the transaxle assembly and transfer assembly in continuous beaded from of 1.2 mm diameter as shown in the illustration. NOTICE: Wipe any grease off from the attaching surfaces. Install it within 10 minutes after applying the se ...

Rear window wiper and washer
Operating the wiper lever Turning the end of the lever turns on the rear window wiper and washer. The illustration is intended as an example. *1 or *2 Intermittent window wiper operation *1 or *2 Normal window wiper operation Washer/wiper dual operation Washer/wiper du ...

В© 2011-2026 Copyright www.tsienna.net