Toyota Sienna Service Manual: Open in Side Squib LH Circuit

Toyota Sienna Service Manual / Supplemental restraint system / Airbag system / Diagnostic trouble code chart / Open in Side Squib LH Circuit

DTC B0116/48 Open in Side Squib LH Circuit

DESCRIPTION

The side squib LH circuit consists of the center airbag sensor assembly and the front seat side assembly LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0116/48 is recorded when an open circuit is detected in the side squib LH circuit.

DTC No.	DTC Detecting Condition	Trouble Area
B0116/48	Open circuit in SFL+ wire harness or SFL- wire harness of side squib LH Side squib LH malfunction Center airbag sensor assembly malfunction	Front seat side airbag assembly LH (Side squib LH) Center airbag sensor assembly Floor wire

INSPECTION PROCEDURE

HINT:

Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (8).
After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH (SIDE SQUIB LH)

CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH (SIDE SQUIB LH)

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the front seat side airbag assembly LH.
Connect the black wire side of SST (resistance 2.1 Ω) to the floor wire.

CAUTION: Never connect a tester to the front seat side airbag assembly LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (5).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs

OK: DTC B0116/48 is not output.

HINT: Codes other than DTC B0116/48 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE FRONT SEAT ASSEMBLY LH

2 CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)

CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST (resistance 2.1 Ω) from the floor wire.
Disconnect the connector from the center airbag sensor assembly.
Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FLOOR WIRE

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

Connect the connectors to the front seat side airbag assembly LH and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (5).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (5).

OK: DTC B0116/48 is not output.

HINT: Codes other than code B0116/48 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Short in Side Squib LH Circuit

DTC B0115/47 Short in Side Squib LH Circuit DESCRIPTION The side squib LH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly LH. This circuit instruc ...

Short to GND in Side Squib LH Circuit

DTC B0117/45 Short to GND in Side Squib LH Circuit DESCRIPTION The side squib LH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly LH. This circuit ...

Other materials:

Roof luggage carrier (if equipped)
Roof luggage carrier components Roof rails Cross rails Adjusting the position of cross rails Turn the knobs counterclockwise to release the cross rails. Slide the cross rails to the appropriate position for loading luggage and turn the knobs clockwise to tigh ...

Problem symptoms table
HINT: Inspect the "Fuse" and "Relay" before confirming the suspected area as shown in the table below. DISPLAY FUNCTION: SOUND FUNCTION: REMOTE CONTROL FUNCTION: *1: without Navigation System *2: with Navigation System ...

TS and CG Terminal Circuit
DESCRIPTION In the sensor check mode, a malfunction of the speed sensor that cannot be detected when the vehicle is stopped is detected while driving. Transition to the sensor check mode can be performed by connecting terminals TS and CG of the DLC3 and turning the ignition switch from off ...