Toyota Sienna Service Manual: Disposal
HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
- When scrapping a vehicle equipped with the SRS or
disposing of the front seat side airbag assembly, be sure to
deploy the airbag first in accordance with the procedure
described below. If any abnormality occurs with airbag
deployment, contact the SERVICE DEPT. of TOYOTA
MOTOR SALES, U.S.A., INC.
CAUTION:
- Never dispose of a front seat side airbag assembly
that has an undeployed airbag.
- The airbag produces an exploding sound when it is
deployed, so perform the operation outdoors and
where it will not create a nuisance to nearby residents.
- When deploying the airbag, always use the specified
SST (SRS Airbag Deployment Tool). Perform the
operation in a place away from electrical noise.
- When deploying the airbag, perform the operation at
least 10 m (33 ft) away from the airbag assembly.
- The front seat side airbag assembly becomes
extremely hot when the airbag is deployed, so do not
touch it for at least 30 minutes after deployment.
- Use gloves and safety glasses when handling a front
seat side airbag assembly with a deployed airbag.
- Do not apply water, etc. to a front seat side airbag
assembly with a deployed airbag.
- Always wash your hands with water after completing
the operation.
1. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (WHEN INSTALLED IN VEHICLE)
HINT:
Prepare a battery as the power source to deploy the
airbag.
- Check the function of the SST (25).
- Precaution.
- Disconnect the cable from the negative battery
terminal.
CAUTION:
Wait for 90 seconds after disconnecting the
cable to prevent the airbag working.
- Remove the 4 bolts from the front seat assembly.
- For Manual Seat
- For Power Seat
HINT:
Keep the front seat assembly in the cabin.
- Install the SST.
- Disconnect the connector (yellow colored one)
from the front seat side airbag assembly.
NOTICE:
When handling the airbag connector, take
care not to damage the airbag wire harness.
- Connect the SST connector to the front seat
side airbag assembly connector.
SST 09082-00700, 09082-00750
NOTICE:
To avoid damaging the SST connector and
wire harness, do not lock the secondary
lock of the twin lock.
- Install the 4 bolts to the front seat assembly.
- For Manual Seat
- For Power Seat
- Move the SST at least 10 m (33 ft) away from
the vehicle front side window.
- Maintaining enough clearance for the SST wire
harness in the front side window, close all
doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire
harness.
- Connect the red clip of the SST to the battery
positive (+) terminal and the black clip of the
SST to the negative (-) terminal.
- Deploy the airbag.
- Check that no one is inside the vehicle or within
a 10 m (33 ft) radius of the vehicle.
- Press the SST activation switch and deploy the
airbag.
CAUTION:
- When deploying the airbag, make sure
that no one is near the vehicle.
- The front seat side airbag assembly
becomes extremely hot when the airbag
is deployed, so do not touch it for at least
30 minutes after deployment.
- Use gloves and safety glasses when
handling a front seat side airbag
assembly with a deployed airbag.
- Do not apply water, etc. to a front seat
side airbag assembly with a deployed
airbag.
- Always wash your hands with water after
completing the operation.
HINT:
The airbag is deployed as the LED of the SST
activation switch comes on.
2. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (WHEN NOT INSTALLED IN
VEHICLE)
NOTICE:
- When disposing of the front seat side airbag
assembly, never use the customer's vehicle to
deploy the airbag.
- Be sure to follow the procedure detailed below
when deploying the airbag.
HINT:
Prepare a battery as the power source to deploy the
airbag.
- Check the function of the SST (25).
- Remove the front seat side airbag assembly.
- Remove the front seat assembly.
- For Manual Seat
- For Power Seat
- Remove the 2 nuts and the front seat side
airbag assembly from the seatback assembly.
CAUTION:
- When removing the front seat side airbag
assembly, work must be started 90
seconds after the ignition switch is
turned to the "LOCK" position and the
negative (-) terminal cable is
disconnected from the battery.
- When storing the front seat side airbag
assembly, keep the airbag deployment
side facing upward.
- Using a service-purpose wire harness for the
vehicle, tie down the front seat side airbag assembly
to the tire.
Wire harness:
Stripped wire harness section:
1.25 mm2 or more (0.0019 in.2 or more)
HINT:
To calculate the area of the stripped wire harness
section:
Area = 3.14 x (Diameter)2 divided by 4
CAUTION:
If the wire harness is too thin or an alternative
object is used to tie down the front seat side
airbag assembly, it may be snapped by the
shock when the airbag is deployed. Always use
a wire harness for vehicle use with an area of at
least 1.25 mm2 (0.0019 in.2).
- Install the 2 nuts to the front seat side airbag
assembly.
- Wind the wire harness around each of the stud
bolts of the front seat side airbag assembly as
shown in the illustration.
- Position the front seat side airbag assembly
inside the tire as shown in the illustration.
Tire size:
Must exceed the following dimensions
Width:
185 mm (7.28 in.)
Inner diameter:
360 mm (14.17 in.)
CAUTION:
- Make sure that the wire harness is tight.
If there is slack in the wire harness, the
front seat side airbag assembly may
become loose due to the shock when the
airbag is deployed.
- Always tie down the front seat side
airbag assembly with the airbag
deployment direction facing inside the
tire.
NOTICE:
The tire will be damaged by airbag
deployment, so use an extra tire.
- Install the SST.
- Connect the SST connector to the front seat
side airbag assembly connector.
SST 09082-00750
- Place the tires.
- Place at least 2 tires under the tire which the
front seat side airbag assembly is tied to.
- Place at least 2 tires over the tire which the
front seat side airbag assembly is tied to. The
top tire should have a disc wheel installed.
NOTICE:
Do not place the SST connector under the
tire because it could be damaged.
- Tie the tires together with 2 wire harnesses.
CAUTION:
Make sure that the wire harness is tight.
Looseness in the wire harness results in the
tires coming free due to the shock when the
airbag is deployed.
- Install the SST.
- Connect the SST connector.
SST 09082-00700
NOTICE:
To avoid damaging the SST connector and
wire harness, do not lock the secondary
lock of the twin lock. Also, secure some
slack for the SST wire harness inside the
tire.
- Move the SST at least 10 m (33 ft) away from
the airbag tied down to the tires.
- Deploy the airbag.
- Connect the red clip of the SST to the battery
positive (+) terminal and the black clip of the
SST to the negative (-) terminal.
- Check that no one is within a 10 m (33 ft) radius
of the tire which the front seat side airbag
assembly is tied to.
- Press the SST activation switch and deploy the
airbag.
CAUTION:
When deploying the airbag, make sure that
no one is near the tire.
HINT:
The airbag is deployed as the LED of the SST
activation switch comes on.
- Dispose of the front seat side airbag assembly.
CAUTION:
- The front seat side airbag assembly becomes
extremely hot when the airbag is deployed,
so do not touch it for at least 30 minutes after
deployment.
- Use gloves and safety glasses when handling
a front seat side airbag assembly with a
deployed airbag.
- Do not apply water, etc. to a front seat side
airbag assembly with a deployed airbag.
- Always wash your hands with water after
completing the operation.
- Remove the front seat side airbag assembly
from the tire.
- Place the front seat side airbag assembly in a
plastic bag, tie it tightly and dispose of it as
other general part disposal.
1. FRONT SEAT SIDE AIRBAG ASSEMBLY (VEHICLE NOT INVOLVED IN COLLISION)
Perform a diagnostic system check.
With the front seat side airbag assembly installed on
the vehicle, per ...
Other materials:
Mass or Volume Air Flow Circuit Range / Performance Problem
DESCRIPTION
Refer to DTC P0100 (See page ES-116).
MONITOR DESCRIPTION
The MAF meter is a sensor that measures the amount of air flowing through the
throttle valve. The ECM
uses this information to determine the fuel injection time and to provide an
appropriate air-fuel ratio.
Insi ...
Camshaft Position Sensor "A" Circuit
DTC P0340 Camshaft Position Sensor "A" Circuit (Bank 1
or Single Sensor)
DTC P0342 Camshaft Position Sensor "A" Circuit Low
Input (Bank 1 or Single Sensor)
DTC P0343 Camshaft Position Sensor "A" Circuit High
Input (Bank 1 or Single Sensor)
DTC P0345 Camshaft Posit ...
SRS Warning Light Remains ON
DESCRIPTION
The SRS warning light is located on the combination meter assembly.
When the SRS is normal, the SRS warning light comes on for approximately 6
seconds after the ignition
switch is turned from the LOCK position to ON position, and then goes off
automatically.
If there is a mal ...