Toyota Sienna Service Manual: Short to B+ in Curtain Shield Squib LH Circuit

Toyota Sienna Service Manual / Supplemental restraint system / Airbag system / Diagnostic trouble code chart / Short to B+ in Curtain Shield Squib LH Circuit

DTC B1168/86 Short to B+ in Curtain Shield Squib LH Circuit

DESCRIPTION

The curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1168/86 is recorded when a short to B+ is detected in the curtain shield squib LH circuit.

DTC No.	DTC Detecting Condition	Trouble Area
B1168/86	Short circuit in curtain shield squib LH wire harness (to B+) Curtain shield squib LH malfunction Center airbag sensor assembly malfunction	Curtain shield airbag assembly LH (Curtain shield squib LH) Center airbag sensor assembly Floor wire

INSPECTION PROCEDURE

HINT:

Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (8).
After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (CURTAIN SHIELD SQUIB LH)

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the curtain shield airbag assembly LH.
Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire.

CAUTION: Never connect a tester to the curtain shield airbag assembly LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (5).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs

OK: DTC B1168/86 is not output.

HINT: Codes other than DTC B1168/86 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH

2 CHECK FLOOR WIRE (CURTAIN SHIELD SQUIB LH CIRCUIT)

CHECK FLOOR WIRE (CURTAIN SHIELD SQUIB LH CIRCUIT)

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST (resistance 2.1 Ω) from the floor wire.
Disconnect the connector from the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.

Standard voltage

Standard voltage

REPAIR OR REPLACE FLOOR WIRE

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connectors to the curtain shield airbag assembly LH and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (5).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (5).

OK: DTC B1168/86 is not output.

HINT: Codes other than code B1168/86 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Short to GND in Curtain Shield Squib LH Circuit

DTC B1167/85 Short to GND in Curtain Shield Squib LH Circuit DESCRIPTION The curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly L ...

Short in Driver Side Squib 2nd Step Circuit

DTC B1180/17 Short in Driver Side Squib 2nd Step Circuit DESCRIPTION The driver side squib 2nd step circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad. ...

Other materials:

Disassembly
1. REMOVE REAR NO. 2 SEAT COVER BEZEL Remove the 5 screws. Disengage the 5 claws and remove the rear No. 2 seat cover bezel. 2. REMOVE REAR SEAT RECLINING COVER LH Remove the 2 screws. Disengage the claw and remove the rear seat reclining cover LH. ...

Folding down the third seats (power seats)
You can operate the power third seats when the shift lever is in P. Before folding the third seats Lower the center head restraint to the lowest position and stow the seat belt buckles. Stow the center seat belt. Folding down the third seatbacks Press the folding/returning ...

Center Airbag Sensor Assembly Malfunction
DTC B1100/31 Center Airbag Sensor Assembly Malfunction DESCRIPTION The center airbag sensor assembly consists of the center airbag sensor assembly, safing sensor, drive circuit, diagnosis circuit and ignition control, etc. It receives signals from the airbag sensor, judges whether or not the ...