Toyota Sienna Service Manual: Short to GND in Front Passenger Side Squib Circuit

Toyota Sienna Service Manual / Supplemental restraint system / Airbag system / Diagnostic trouble code chart / Short to GND in Front Passenger Side Squib Circuit

DTC B0107/51 Short to GND in Front Passenger Side Squib Circuit

DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor assembly and the front passenger airbag assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0107/51 is recorded when a short to ground is detected in the front passenger side squib circuit.

DTC No.	DTC Detecting Condition	Trouble Area
B0107/51	Short circuit in front passenger side squib wire harness (to ground) Front passenger side squib malfunction Center airbag sensor assembly malfunction	Front passenger airbag assembly (Front passenger side squib) Center airbag sensor assembly Instrument panel wire

INSPECTION PROCEDURE

HINT:

Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (8).
After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the front passenger airbag assembly.
Connect the black wire side of SST (resistance 2.1 Ω) to the instrument panel wire.

CAUTION: Never connect a tester to the front passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (5).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (5).

OK: DTC B0107/51 is not output. HINT: Codes other than DTC B0107/51 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE FRONT PASSENGER AIRBAG ASSEMBLY

2 CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE SQUIB CIRCUIT)

CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE SQUIB CIRCUIT)

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST (resistance 2.1 Ω) from the instrument panel wire.
Disconnect the connector from the center airbag sensor assembly.
Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

Connect the connectors to the front passenger airbag assembly and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (5).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (5).

OK: DTC B0107/51 is not output. HINT: Codes other than code B0107/51 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Open in Front Passenger Side Squib Circuit

DTC B0106/54 Open in Front Passenger Side Squib Circuit DESCRIPTION The front passenger side squib circuit consists of the center airbag sensor assembly and the front passenger airbag assembly. ...

Short to B+ in Front Passenger Side Squib Circuit

DTC B0108/52 Short to B+ in Front Passenger Side Squib Circuit DESCRIPTION The front passenger side squib circuit consists of the center airbag sensor assembly and the front passenger airbag asse ...

Other materials:

Data list / active test
HINT: By accessing the DATA LIST displayed on the intelligent tester, you can perform such functions as reading the values of switches and sensors without removing any parts. Reading the DATA LIST as the first step in troubleshooting is one method to shorten labor time. 1. DATA LIST FOR CENTER ...

Display Signal Circuit between Radio and Navigation Assembly and Television Camera Assembly
DESCRIPTION This is the display signal circuit of the television camera assembly. WIRING DIAGRAM INSPECTION PROCEDURE 1 CHECK HARNESS AND CONNECTOR (RADIO AND NAVIGATION ASSEMBLY - TELEVISION CAMERA ASSEMBLY) Disconnect the R10 connector from the radio and navigation assembly. &nbs ...

Front seat frame with adjuster
Inspection 1. INSPECT FRONT SEAT ADJUSTER SUB-ASSEMBLY LH Check operation of the seat frame (slide motor). Check if the seat frame moves smoothly when the battery is connected to the slide motor connector terminals. OK If the result is not as specified, replace t ...