Toyota RAV4 manuals

Toyota Sienna Service Manual: Short to GND in Rear Curtain Shield Squib LH Circuit

DTC B1637/85 Short to GND in Rear Curtain Shield Squib LH Circuit

DESCRIPTION

The rear curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B1637/85 is recorded when a short to ground is detected in the rear curtain shield squib LH circuit.

DTC No.

DTC Detecting Condition

Trouble Area

B1637/85

  • Short circuit in rear curtain shield squib LH wire harness (to ground)
  •  Rear curtain shield squib LH malfunction
  •  Center airbag sensor assembly malfunction
  • Curtain shield airbag assembly LH (Rear curtain Shield Squib LH)
  •  Center airbag sensor assembly
  •  Floor wire

INSPECTION PROCEDURE

HINT:

1 CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (REAR CURTAIN SHIELD SQUIB LH)

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (REAR CURTAIN SHIELD SQUIB LH)

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the curtain shield airbag assembly LH.
  4. ) Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire.

CAUTION: Never connect a tester to the curtain shield airbag assembly LH (Rear curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory (5).
  4.  Turn the ignition switch to the LOCK position.
  5. Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs (5).

OK: DTC B1637/85 is not output.

HINT: Codes other than DTC B1637/85 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH

2 CHECK FLOOR WIRE (REAR CURTAIN SHIELD SQUIB LH CIRCUIT)

CHECK FLOOR WIRE (REAR CURTAIN SHIELD SQUIB LH CIRCUIT)

  1. Turn the ignition switch to the LOCK position.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the floor wire.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5.  Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE FLOOR WIRE

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the curtain shield airbag assembly LH and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory (5).
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs (5).

OK: DTC B1637/85 is not output.

HINT: Codes other than code B1637/85 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Open in Rear Curtain Shield Squib LH Circuit
DTC B1636/88 Open in Rear Curtain Shield Squib LH Circuit DESCRIPTION The rear curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly ...

Short to B+ in Rear Curtain Shield Squib LH Circuit
DTC B1638/86 Short to B+ in Rear Curtain Shield Squib LH Circuit DESCRIPTION The rear curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag ...

Other materials:

Integrated Universal Remote Control
Concept The integrated Universal Remote Control in the interior mirror can operate up to 3 functions of remote-controlled systems such as garage door drives, barriers, or lighting systems. General information The Integrated Universal Remote Control replaces up to 3 different hand-held transmitters. ...

Concept, General information, Safety information
Concept The system monitors tire inflation pressure in the four mounted tires. The system warns you if there is a loss of pressure in one or more tires. General information Sensors in the tire valves measure the tire inflation pressure and tire temperature. The system detects the mounted tires auto ...

Distance Control ECU Malfunction
DTC P1617 Distance Control ECU Malfunction DESCRIPTION In the dynamic laser cruise control system, the ECM and the distance control ECU communicate with one another to control the system based on some designation information. If the designation information of the ECM and distance control ECU ...

В© 2011-2023 Copyright www.tsienna.net