Toyota Sienna Service Manual: Short in Front Passenger Side Squib Circuit

Toyota Sienna Service Manual / Supplemental restraint system / Airbag system / Diagnostic trouble code chart / Short in Front Passenger Side Squib Circuit

DTC B0105/53 Short in Front Passenger Side Squib Circuit

DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor assembly and the front passenger airbag assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0105/53 is recorded when a short circuit is detected in the front passenger side squib circuit

DTC No.	DTC Detecting Condition	Trouble Area
B0105/53	Short circuit between P+ wire harness and P- wire harness of front passenger side squib Front passenger side squib malfunction Center airbag sensor assembly malfunction	Front passenger airbag assembly (Front passenger side squib) Center airbag sensor assembly Instrument panel wire

WIRING DIAGRAM

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester
After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road

1 CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the front passenger airbag assembly.
Connect the black wire side of SST (resistance 2.1 Ω) to the instrument panel wire.

CAUTION: Never connect a tester to the front passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (5).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (5).

OK: DTC B0105/53 is not output. HINT: Codes other than DTC B0105/53 may be output at this time, but they are not related to this check.

Go to step 2

REPLACE FRONT PASSENGER AIRBAG ASSEMBLY

2 CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE SQUIB CIRCUIT)

CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE SQUIB CIRCUIT)

Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST (resistance 2.1 Ω) from the instrument panel wire.
Disconnect the connector from the center airbag sensor assembly.
Release the activation prevention mechanism built into connector "B" (7).
Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

Connect the connectors to the front passenger airbag assembly and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (5).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (5).

OK: DTC B0105/53 is not output. HINT: Codes other than code B0105/53 may be output at this time, but they are not related to this check.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

USE SIMULATION METHOD TO CHECK

Short to B+ in Driver Side Squib Circuit

DTC B0103/12 Short to B+ in Driver Side Squib Circuit DESCRIPTION The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad. The circui ...

Open in Front Passenger Side Squib Circuit

DTC B0106/54 Open in Front Passenger Side Squib Circuit DESCRIPTION The front passenger side squib circuit consists of the center airbag sensor assembly and the front passenger airbag assembly. ...

Other materials:

Removal
1. REMOVE REAR WHEEL 2. REMOVE TAIL EXHAUST PIPE ASSEMBLY (See page EX-8) 3. SEPARATE REAR SPEED SENSOR (a) Remove the bolt and the speed sensor from the axle carrier. NOTICE: Be careful not to damage the speed sensor Prevent foreign matter from adhering to the speed sensor. 4. REMO ...

Shift Solenoid "E" Control Circuit
DESCRIPTION Shifting from 1st to 5th is performed in combination with "ON" and "OFF" operation of the shift solenoid valves SL1, SL2, SL3, S4 and SR which are controlled by the ECM. If an open or short circuit occurs in either of the shift solenoid valves, the ECM cont ...

Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance
DTC P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance HINT: This DTC relates to the Accelerator Pedal Position (APP) sensor. DESCRIPTION Refer to DTC P2120 MONITOR DESCRIPTION The accelerator pedal position sensor is mounted on the accelerator pedal ...