Toyota RAV4 manuals

Toyota Sienna Service Manual: Short in Side Squib LH Circuit

DTC B0115/47 Short in Side Squib LH Circuit

DESCRIPTION

The side squib LH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

DTC B0115/47 is recorded when a short circuit is detected in the side squib LH circuit.

DESCRIPTION

WIRING DIAGRAM

WIRING DIAGRAM

INSPECTION PROCEDURE

HINT:

1 CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH (SIDE SQUIB LH)

CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY LH

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the connectors from the front seat side airbag assembly LH.
  4.  Connect the black wire side of SST (resistance 2.1 Ω) to the floor wire.

CAUTION: Never connect a tester to the front seat side airbag assembly LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE: Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.

SST 09843-18060

  1.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  2.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  3.  Clear the DTCs stored in memory.
  4.  Turn the ignition switch to the LOCK position.
  5.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  6.  Check the DTCs.

OK: DTC B0115/47 is not output.

HINT: Codes other than DTC B0115/47 may be output at this time, but they are not related to this check.

REPLACE FRONT SEAT ASSEMBLY LH

2 CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)

CHECK FLOOR WIRE

  1. Turn the ignition switch to the LOCK position.
  2.  Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3.  Disconnect the SST (resistance 2.1 Ω) from the floor wire.
  4.  Disconnect the connector from the center airbag sensor assembly.
  5. Release the activation prevention mechanism built into connector "B".
  6. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

3 CHECK CENTER AIRBAG SENSOR ASSEMBLY

CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. Connect the connectors to the front seat side airbag assembly LH and the center airbag sensor assembly.
  2.  Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  3.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  4.  Clear the DTCs stored in memory.
  5.  Turn the ignition switch to the LOCK position.
  6.  Turn the ignition switch to the ON position, and wait for at least 60 seconds.
  7.  Check the DTCs.

OK: DTC B0115/47 is not output.

HINT: Codes other than code B0115/47 may be output at this time, but they are not related to this check.

USE SIMULATION METHOD TO CHECK

USE SIMULATION METHOD TO CHECK
DTC B0113/42 Short to B+ in Side Squib RH Circuit DESCRIPTION The side squib RH circuit consists of the center airbag sensor assembly and the front seat side airbag assembly RH. This circuit i ...

Open in Side Squib LH Circuit
DTC B0116/48 Open in Side Squib LH Circuit DESCRIPTION The side squib LH circuit consists of the center airbag sensor assembly and the front seat side assembly LH. This circuit instructs the S ...

Other materials:

Rear view monitor system precautions
Area displayed on screen The rear view monitor system displays an image of the view from the bumper of the rear area of the vehicle. The image on the rear view monitor system can be adjusted. The area displayed on the screen may vary according to vehicle orientation conditions. ...

Rear Clearance Sonar Sensor LH Circuit
DESCRIPTION An ultrasonic sensor consists of a sensor portion that transmits and receives ultrasonic waves and a preamplifier that amplifies them. The ultrasonic sensor outputs the ultrasonic waves and sends the received signals to the clearance warning ECU. WIRING DIAGRAM INSPECTION PR ...

Initialization
1. RESET When the back door lock is replaced: The power back door ECU cannot receive a switch signal from the lock. This may cause the power back door system to enter fail-safe mode and DTC B2215 to set, and also make the system disabled. When the lock is replaced, be sure to perform t ...

В© 2011-2026 Copyright www.tsienna.net