Toyota RAV4 manuals

Toyota Sienna Service Manual: Removal

1. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

2. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

3. REMOVE FRONT PILLAR GARNISH LH

4. REMOVE FRONT PILLAR GARNISH RH

5. REMOVE VISOR ASSEMBLY LH

6. REMOVE VISOR ASSEMBLY RH

7. REMOVE ASSIST GRIP SUB-ASSEMBLY (2)

8. REMOVE VISOR HOLDER (1)

9. REMOVE ROOF CONSOLE BOX ASSEMBLY

10. REMOVE SUN ROOF OPENING TRIM MOULDING (W/ SLIDING ROOF)

11. REMOVE INNER REAR VIEW MIRROR ASSEMBLY

12. REMOVE ROOF HEADLINING ASSEMBLY (4)

13. REMOVE FRONT WIPER ARM HEAD CAP

14. REMOVE FRONT WIPER ARM LH

15. REMOVE FRONT WIPER ARM RH

16. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

17. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

18. REMOVE COWL TOP VENTILATOR LOUVER SUBASSEMBLY

19. REMOVE WINDSHIELD MOULDING OUTER UPPER

REMOVE WINDSHIELD MOULDING OUTER UPPER

  1.  Using a knife, cut off the moulding, as shown in the illustration.

    NOTICE: Do not damage the vehicle body with the knife.

  2.  Remove the remaining moulding.

    HINT: When removing, make a partial a cut, then pull and remove it by hand.

  3.  w/ Deicer: Disconnect the connector, as shown in the illustration.

20. REMOVE WINDSHIELD GLASS

REMOVE WINDSHIELD GLASS

  1.  Pass a piano wire between the vehicle body and glass from the interior.

REMOVE WINDSHIELD GLASS

  1. Tie both wire ends to wooden blocks or similar objects.

HINT: Apply protective tape to the outer surface of the vehicle body to prevent its surface from being scratched.

NOTICE:

  1.  Cut off the adhesive by pulling piano wire around the glass.
  2.  Disengage the stoppers.
  3.  Using a suction cup, remove the glass.

NOTICE: Leave as much adhesive on the vehicle body as possible when removing the glass.

21. CLEAN WINDSHIELD GLASS

CLEAN WINDSHIELD GLASS

  1.  Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.
  2.  Clean the outer circumference of the glass with white gasoline.

NOTICE: Do not touch the glass surface after cleaning it.

Windshield glass
COMPONENTS ...

Installation
1. INSTALL WINDSHIELD GLASS NO.2 STOPPER  Coat the installation part of the stoppers with Primer G. NOTICE:  Allow the primer coating to dry for 3 minutes or more.   ...

Other materials:

Write vin
(a) The VIN writing process is shown in the flowchart below. This process allows the VIN to be input into the ECM. If the ECM is changed, or the ECM VIN and Vehicle VIN do not match, the VIN can be registered, or overwritten in the ECM by following this procedure. (b) Write VIN using the int ...

Pressing Power Switch does not Turn on System
INSPECTION PROCEDURE 1 CHECK CABIN Check that conditions in the cabin are not likely to cause condensation. HINT: This problem occurs when the cabin is humid and the temperature rapidly changes. This condition may produce condensation, resulting in a short circuit. OK: Condensation ...

Open or Short Circuit in ABS Motor Relay Circuit
DESCRIPTION The ABS motor relay supplies power to the ABS pump motor. While the ABS & TRAC & VSC are activated, the ECU switches the ABS motor relay ON and operates the ABS pump motor. WIRING DIAGRAM INSPECTION PROCEDURE 1 PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AB ...

В© 2011-2023 Copyright www.tsienna.net